Hi! Who can help me. I have memory ED18L3265C. I would have info and
pinout.
Best regards. John.

I am despartely searching for a small pcb mountable air pump to generate
5psig.    

This would be similiar to the pumps used in the over the counter blood
pressure monitors that use a small pump to inflate the cuff.

Thanks!

Mark

–
 Mark D Doble
 Hewlett-Packard               m…@atl.hp.com
 Atlanta, Georgia USA  

I have an old Kenwood Power Amplifier for a car stereo that I would like
to put back into service.  The amp is a model KAC-424 and sports two
Toshiba amplifier chips for the power output.  My problem is that the
two Toshiba chips are literally blown out.  I mean they each have a hole
in them that looks like a minor explosion took place inside. This has
caused the lettering on the front of the chip to be partially obscured.
What I can read from whats left is this,

                        TA 7250..
(the dots indicate numbers that are probably there but I can’t make
out.)

If anyone can shed light on what the likely complete indentifier is for
the IC I would be grateful.  I also can’t locate a source for Toshiba
chips so if anyone knows of a source of Toshiba (or equivalent) chips
that would most appreciated also.  Thanks in advance.

-John

Hi netters!

Who has experience with BASIC programmable microcontrollers?
We are looking for a both controler + necessary software for programming
the chip.

Any help very much appreciated!

Please answer to schi…@uni-muenster.de – Thanx!

——————————————————
H. Schiller
Institut fuer Pharmazeutische Biologie und Phytochemie
Hittorfstrasse 56                            
D-48149 Muenster – Germany
eMail: schi…@uni-muenster.de
——————————————————

Does anyone have stock of a Motorola SG1525AJ Pulse Width Modulator. We
require a small number to complete a contract. This device was also made
by Silicon General among others but only the Motorola part worked in our
system.

From article <55pppn$…@jagalchi.cc.pusan.ac.kr>, by sss…@hyowon.cc.pusan.ac.kr (shin seoksoo):

> :Nice meet to you
> :I AM A STUDENT IN KOREA
> :I WANT TO KNOW WHAT HALL EFFECT IS.
> :IF YOU ANSWER MY QUESTION, I THANK TO YOU.

Take a conductor of nonzero width, say a conducting ribbon, and put it
in a magnetic field, where the field is perpendicular to the ribbon.
Then allow current to flow along the length of the ribbon.  A voltage
will develop across the ribbon.  This is the Hall effect.  Here is a
picture:
                         Field
                voltage    /\
                        +  ||
          _______________\_________________
          \                                \
      ==>  \                                \  ==> current
            \________________________________\
                             \
                           /\ –
                           ||   voltage

Why is there a voltage?  Because the field deflects moving electrons
away from the + edge and towards the – edge.

Hall effect sensors use this effect to sense magnetic fields.

                                Doug Jones
                                jo…@cs.uiowa.edu

I am looking for a source of hollow conductor copper wire (in the 10-14
gauge range) for use in a water-cooled coil.  

I have seen references to it, but never the name of a supplier.  The
alternative would be fine copper tubing, but it may not have enough
copper left, and would not be insulated.

Thanks.

- Barry

–
Dr. Barry Megdal
Electrical Engineering Dept.
Caltech  136-93
Pasadena, CA  91125
bmeg…@caltech.edu

Hi,
        I was wondering where I could buy some NiMH batteries, ‘plain’ ones,
not the ones with built-in chargers.

Thanks,

Chafik Hankour.
Tufts University.

Could anyone help me finding a source/vendor:
I need a Laser Diode:
        670 nM (or may be 680 nM)
        10 mW of  optical output power.

For 1.5 mRad of aperture, Do I need a lens ?

Thank you.

EE Christian Ledwith
sl…@impsat1.com.ar

442 pin, ZIF socket AMP Socket 3, have more than 7,000.
Would like $.25 each, will negotiate.

tomgr…@primenet.com
fax 208-375-7516